Best material for making a bearing puller strong back

X

If you are looking for more details, kindly visit puller supplier.

Notice

This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.

(Q) How should I maintain my Safe-T-Puller™ or Safe-T-Hauler™?

(A)

• Soap down and rinse off with fresh water after each use.
• Keep electrical terminals well lubricated with dielectric grease.

• DO NOT SUBMURGE MOTOR OR ELECTRICAL COMPONENTS.
• IMPORTANT! ALWAYS KEEP INNER NUT ON STUDS FROM TURNING WHEN REMOVING ELECTRICAL WIRING.

(Q) Do I need to re-grease the planetary gears inside my Safe-T-Puller™ or Safe-T-Hauler™ ?

(A)

• There is no need to re-grease the planetary gears in your Safe-T-Puller™ or Safe-T-Hauler™.
• The Safe-T-Puller™ and Safe-T-Hauler™ has a life-time sealed planetary reduction gear lubricated with an EP2 rated lithium based grease that adheres to the planetary gears and is long lasting.
• Taking the reduction gear unit apart will break the housing’s seal and void your warranty.
• It will be necessary to return the unit to the factory to have the housing re-sealed.

(Q) How long will the bonded rubber lining on the sheaves last?

(A)

• The bonded rubber will last for many seasons.
• It is a wearable part and can be replaced.
• Be sure the pot line does not slip in the sheave.
• Line slippage will wear the bonded rubber, shortening its life expectancy.
• Use a downward pull on the line if it starts to slip.
• Sea grass and slime may cause your line to slip slightly.
• Ensure your lines are maintained clean.
• It sometimes helps to reverse the pot line end for end when leaving your pots out for extended lengths of time.

(Q) How much current does the Safe-T-Puller™ or Safe-T-Hauler™ draw?

(A)

• The Sports Model is rated at 1.1 HP 12 Volt DC and draws approximately 15-40 Amps depending on the load.
• The Alaskan Sports Model is rated at 1.6 HP 12Volt DC, and draws approximately 20-60 Amps depending the on load.
• The Light Commercial Model is rated at 2.1 HP 12 Volt DC, and draws approximately 30-80 Amps depending on the load.

(Q) How fast will the Safe-T-Puller™ or Safe-T-Hauler™ pull my pot?

(A)

• The Sports Model is rated to pull 90-100 Feet Per Minute (FPM)
• The Alaskan Sports Model is rated to pull 100-110 Feet Per Minute (FPM)
• The Light Commercial Model is rated to pull 110-120 Feet Per Minute (FPM)

(Q) How much weight can the Safe-T-Puller™ or Safe-T-Hauler™ pull?

(A)

• The Sports Model has a rated capacity of 100 lbs.
• The Alaskan Sports Model has a rated capacity of 200 lbs.
• The Light Commercial Model has a rated capacity of 300 lbs.
• Many customers pull strings of 5, 10 or more pots on a pot line (where legal) using the Light Commercial Model.

(Q) Will the Safe-T-Puller™ or Safe-T-Hauler™ hold its load while hoisted?

(A)

Contact us to discuss your requirements of 4 inch magnetic bowl. Our experienced sales team can help you identify the options that best suit your needs.

• The Safe-T-Puller™ and Safe-T-Hauler™ units will hold their loads up to a point because of the high gear ratio.
• However, it is NOT good safety practice to depend upon this gear ratio to hold a heavy load as it may back down the motor.
• This would be similar to relying on placing the manual transmission on your vehicle to hold it in place on a steep hill – without setting the emergency brake.
• A better solution would be to secure the free end of the line to a cleat securely fastened to your boat or to the davit.

(Q) What is the difference between the Safe-T-Puller™ and the Safe-T-Hauler™ ?

(A)

• The Safe-T-Puller™ hangs from a swivel pivot mount at the end of the davit similar to many commercial hydraulic style puller designs.
• The Safe-T-Puller™ now comes equipped with a roller fairlead giving much greater line control under heavy sea and wind conditions.
• The Safe-T-Hauler™ powerhead is mounted on the davit close to the gunnel.
• The pot line is pulled through a FRP Block hanging from the davit end.
• The Safe-T-Hauler™ has a built-in roller fairlead increasing line wrap and pulling capacity.
• The Safe-T-Hauler™ design results in a very compact take-apart design that is extremely strong and portable.
• Generally, crabbers and shrimpers from the Pacific Northwest and Alaska prefer the Safe-T-Puller™ style.
• Fishermen with boating experience on the East coast seem to prefer the Safe-T-Hauler™.
• It is more of an individual’s preference as they are both highly proven and reliable designs.

(Q) What makes the Safe-T-Puller™ and Safe-T-Hauler™ better than your competitors pullers?

(A)

• The Safe-T-Puller™ and Safe-T-Hauler™ powerhead reduction gear unit uses hardened Steel Planetary Gears that are much stronger than the competitor’s models. They use a worm drive gear mechanism that is made of brass. The reduction gear unit is a “Planetary Differential” design that is much stronger than the worm gear drive.
• Quality Products NW uses only the Highest Quality Stainless Steel and Marine Grade Components in our Safe-T-Puller™ and Safe-T-Hauler™ products.
• We place Safety (your safety) as number one followed by Product Quality as number two.
• Our Safe-T-Puller™ and Safe-T-Hauler™ products carry a full 90-day warranty against material or workmanship defects.
• We also offer an Extended Warranty up to 3 years.
• Go to any marina on the West Coast or Alaska and you will very likely see a number of Quality Products NorthWest Pullers and Haulers mounted on recreational boats. Best advice is talk to an owner of one!
• The Department of Fish and Game in Alaska uses our products for “checking pots” for shell fish regulation compliance.
• The Department of Fisheries in Washington State replaced their electric pullers (our competition’s models) on their Fisheries Enforcement’s Boats with our electric “Light-Commercial Safe-T-Puller™ ” models. That pretty much speaks for itself.

(Q) What options are available with the Safe-T-Puller™ / Safe-T-Hauler™ ?

(A)

• Many options are available. (For example: you can use our New Scotty Downrigger Bracket for ease of mounting and convenience.
• One(1) and two(2) piece quick-detach davits are available.
• Different configurations for Gunnel Brackets and Kick-Plate Brackets are offered.
• Custom Stainless Steel Davits and Custom sized and designed Davits to fit your particular boating needs.
• Talk with our friendly staff to discuss your particular requirements. We will work with you to help you get the special unit you want.

(Q) Can I buy direct from Quality Products NorthWest, LLC?

(A)

• We are a manufacturing firm and do not sell direct to the public.
• We have worked to establish a dealer network to better serve you with your pot puller selection and installation.
• To locate a dealer nearest you, please look in our Dealer List or give our friendly customer support staff a call.

(Q) Does Quality Products NorthWest, LLC manufacture other products besides the Safe-T-Puller™ and Safe-T-Hauler™ ?

(A)

• Yes! We manufacture High Quality Crab and Shrimp Pots.
• These traps will out perform any other traps on the market.
• Our designs are proven after many years of experience and testing.
• Our pot and trap products are much higher quality and more durable (rugged) than cheap imports.
• Please see our Product List for a complete selection of our Crab and Shrimp Trap line.

(Q) What kind of electrical switch does the Safe-T-Puller™ and Safe-T-Hauler™ use?

(A)

• Our Safe-T-Puller™ and Safe-T-Hauler™ units are operated by using an air-activated foot switch that controls a heavy-duty marine coated solenoid.
• We call this unit the “Safe-Switch” which is now standard equipment with all of our puller and hauler models.
• Using the air-activated control means that there is no possibility of contact between the electrical current and any salt water on your boat deck.
• This is a “Safer Product” than any other design we have seen.

(Q) What is the gear ratio for the Reduction Gears?

(A)

• The reduction gear is a “Differential Planetary” design that is an extremely strong and reliable unit.
• The Gear ratio is 159:1.
• This means that the 12 VDC motor turns 159 revolutions for every revolution of the sheave.
• Our reduction unit is sealed and life-time lubricated with a high pressure EP2 rated lithium based grease.
• The motor assembly is O-Ring sealed to prevent saltwater intrusion from spray or wash down.
• Many customers pull strings of 5, 10 or more pots on a pot line (where legal).
• We have many units that have been in service for over 11 years with no breakdowns or repairs.
• Our competition cannot make the same claim.

• NEVER SUBMURGE POWER UNIT, MOTOR OR ELECTRICAL COMPONENTS
  

For more large volume sand blasters cabinet supplierinformation, please contact us. We will provide professional answers.