Brass is a metal that looks good with wood, is easy to work, and can be soldered. You can use it for specific parts or create entire automaton with it! If you are going to use brass, probably the first thing you’ll want to do is cut some. It comes in all kinds of shapes and sizes. Let’s take a look at some of the more common formats and how to cut them. Remember to wear safety glasses when using any of these techniques.
For more Brass Tools For Saleinformation, please contact us. We will provide professional answers.
How to Cut Brass Rod
Cutting Brass Rod with Cutting Pliers
For smaller sizes of wire and rod, wire cutters will do the job. For larger gauges, you may need to use a larger pair of cutting pliers or bolt cutters for the really big stuff. With any of these tools, place the rod as far into the jaws as possible to make the cut. Some wire cutters leave the cut rod with a sharp, unsightly end. You will probably want to file, sand, or grind the end of the freshly cut rod so that it is flat.
Cutting Brass Rod with a Hacksaw
Place the rod to be cut in a sturdy vise. Try to make the cut as close to the vise as possible to minimize vibration. The hacksaw is a two-handed tool. Place one hand on the handle and your second hand on the end of the hacksaw frame. The saw cuts when you are pushing the tool away from your body. Start the cut with short strokes using the part of the blade nearest the handle. Once there is a groove for the blade to sit in, use both your arms and shifting body weight to make each cutting stroke. Not much downward pressure is needed, and then only when pushing the saw. A long, steady stroke that uses the full length of the blade is preferable to short, frantic stokes. Pay attention and slow down as you come close to cutting through the metal so the saw doesn’t cut something it’s not supposed to.
How to Cut Brass Tubing
Sawing Brass Tubing
You can use small and large metal saws to cut brass tubing. I’d recommend doing it in a small hobby mitre box or a groove you have cut into a piece of wood. Place the tubing in one of the mitre box grooves and begin the cut. As the saw makes its way through the tubing, it will begin to cut two walls at once. This can cause the saw to bind, making sawing difficult. To avoid this, slowly rotate the tubing away from you so that you are only sawing through one wall of the tubing at any given time.
Using a Tubing Cutter
You can buy special cutters designed to cut metal tubing. The tool is clamped to the tubing and a circular blade progresses through the metal. Fasten the tool where the cut is to be made. Spin the tool around the tubing several times. Turn the knob a little to bring the blade against the tubing, and rotate again. Repeat this until the tubing has been divided. Don’t tighten the knob much or the tubing may end up with a crimped end. If this should happen, a tapered reamer can be used to spread opening. File the crimped end off or use a stationary belt sander to finish the edge. Cut the piece a little long to account for any amount that may need to be filed or sanded away.
Cutting Brass Sheet
Cutting Brass Sheet with Shears & Snips
Brass sheet can be cut with metal shears and snips. The type I often use are called aviation snips. These come in three varieties: right-cutting, left-cutting, and straight-cutting. These usually have green, red, and yellow handles respectively. Despite the name, the straight-cutting variety can be used to cut curves — outside curves at least. When cutting a circle, trim the corners off the piece repeatedly until it starts to look like a circle made of straight cuts. Then, make the final curved cut using the inside of the jaws. If precision is required, it’s a good idea to cut outside of the desired line, then use a file to finish the job.
Cutting Brass Sheet with a Hacksaw
Straight cuts in brass sheet can also be made with a hacksaw. Place the brass between two sheets of scrap plywood and clamp all three pieces in a vise. The wood supports the metal during the cut. If you need to see a marked line on the surface of the brass, place a sheet of plywood on the back side of the brass only. Be mindful to only exert downward pressure when pushing the saw.
If you want to learn more, please visit our website Non-Sparking Cutting Tools.
Cutting Brass Sheet with a Jeweler’s Saw and Bench Pin
With practice, a jeweler’s saw used in conjunction with a bench pin will allow you to cut very intricate shapes out of brass sheet. The V-shaped notch in the bench pin is used to support the metal on both sides of the blade. The saw is held vertically, with the handle on the bottom and the saw teeth facing away from you. You basically look down on the saw as you make a cut. Here are a few rules of thumb I’ve found helpful.
First, make sure the blade is taught in the saw frame and the slant of the saw teeth point down toward the handle. Rub beeswax or a commercial lubricant such as ‘Cut Lube’ on the back of the saw blade. With the metal resting flat on the bench pin, start the cut with the saw at a 45 degree angle, the top of the saw frame pointing away from you. Once a groove for the blade has been established, bring the saw upright so that it is perpendicular to the material being cut. Use long, slow, rhythmic strokes and don’t force the saw. When cutting curves, turn and guide the metal into the blade. Never place a finger in front the blade — even if it is some distance away. These thin blades break often.
Cutting Brass with a Rotary Tool
A handy motorized rotary tool can also cut brass rod, tubing, and sheets. See Tips article number 6, 21 Rotary Tool Tips and Tricks for Automaton-Makers, for details on how to use this tool to cut metals. Be sure to clamp the rod in a vise, put on heavy gloves, and wear eye protection.
This article only covers some of the many ways to cut brass. There are more techniques to discover used in a variety of trades and crafts! I hope you’ll find and share them.
Dug’s Automata Tips, Techniques and Tricks
A quarterly column by automaton-maker and enthusiast Dug North
Copyright 2014 Dug North
Warning: The topics covered in this column include the use of tools and materials that have the potential to cause damage to property and/or bodily injury. Your safety is important and it is your sole responsibility. Always read and follow the safety instructions that come with tools and materials you use. Wear safety glasses, use guards and other forms of safety equipment, follow safety precautions, and use good judgment. Seek the guidance of experienced outside sources whenever required.
Further Reading
Complete Metalsmith: Professional Edition by Tim McCreigh: Amazon UK – Amazon US
Tools and Their Uses by U.S. Bureau of Naval Personnel: Amazon UK – Amazon US
Materials
Brass Rod: Amazon UK – Amazon US
Brass Tubing: Amazon UK – Amazon US
Brass Sheet: Amazon UK – Amazon US
Tools
Cutting Pliers: Amazon UK – Amazon US
Hacksaw: Amazon UK – Amazon US
Mini Hacksaw: Amazon UK – Amazon US
Hobby Saw Mitre Box: Amazon UK – Amazon US
Tubing Cutter: Amazon UK – Amazon US
Aviation Snips: Amazon UK – Amazon US
Jeweler’s Saw and Blades: Amazon UK – Amazon US
Bench Pin: Amazon UK – Amazon US
Cut Lube: Amazon UK – Amazon US
For more information, please visit non sparking shovel.