You will get efficient and thoughtful service from JINHUA HARDFACING.
Companies thinking of making a change to the SAW process should consider the numerous benefits it offers, as well as some key best practices to help them get the most from the investment. (photo courtesy of Miller Electric Mfg. Co.)The submerged arc welding (SAW) process can offer significant benefits in many fabrication and manufacturing welding applications from increased productivity to improved operator comfort and consistent high quality welds.
Companies thinking of making a change to the SAW process should consider the numerous benefits it offers, as well as some key best practices to help them get the most from the investment.
Submerged arc basics
The SAW process is well-suited to demanding heavy industrial applications, such as pipe, pressure vessel and tank, railcar manufacturing and heavy construction/mining. Applications that require high productivity rates or that involve very thick materials can especially benefit from the SAW process.
The high deposition rates and travel speeds that can be achieved with SAW and the significant impact these can have on an operations productivity, efficiency and bottom line are among the key benefits of the process.
Other benefits include the excellent chemical and mechanical properties of finished welds, minimal arc visibility and low fume that result in improved operator comfort, and good weld bead shapes and toes lines.
Submerged arc welding is a wire-fed process that uses a granular flux to shield the arc from the atmosphere. As the name suggests, the arc itself is buried in the flux, meaning the arc is not visible when parameters are correctly set with a sufficient layer of flux. The wire is fed through a torch that moves along the weld joint, and SAW can be used in single torch and multi-torch configurations. The arc heat melts a portion of wire, flux and base material to form a molten weld pool. The molten flux and metal freeze to form a slag-covered weld bead behind the arc.
With the SAW process, welded metal thickness can range from 1/16 inch to ¾ inch thickness for a single pass, with 100 percent joint penetration, and unlimited metal thickness on multi-pass welds provided the proper joint preparation and wire/flux combination are employed.
Flux and wire selection
Choosing the proper flux and wire for the specific SAW application is critical to achieving optimal results with the process. While the SAW process alone is a highly efficient one, productivity and efficiency can be enhanced even more based upon the wire and flux used.
Flux is a crucial component that not only shields the weld puddle, but also contributes to mechanical properties and, ultimately, the productivity gains that are possible. The formulation of the flux is the great influencer on these factors impacting the current-carrying capacity and slag release. Current-carrying capacity refers to the maximum current where the highest possible deposition rates and high-quality weld profiles can be obtained. The slag release of a specific flux impacts flux choice because some are better suited for certain joint designs than others.
Options in flux selection for SAW include active and neutral type fluxes. One basic difference: active fluxes change the chemistry of the weld, whereas neutral fluxes do not. Active fluxes contain silicon and manganese, in particular. These elements help maintain tensile strength at higher heat inputs, help welds wet out smoothly and provide good slag release at higher travel speeds. Overall, active slags can help reduce the risk of poor weld quality, as well as costly post-weld cleaning and rework. Keep in mind, however, that active fluxes are generally best suited for single or two-pass welding. Neutral fluxes are better for large multi-pass welds because they help avoid forming brittle, crack-sensitive weldments. When choosing a neutral flux, look for one with the lowest basicity index that still provides the necessary mechanical properties.
There are also many choices regarding SAW wire selection, each with strengths and weaknesses. Some wires are formulated for welding at higher heat inputs, while others are specifically designed with alloys that help the flux with weld cleaning. Be aware that the wire chemistry and heat input interact to impact the mechanical properties of the weld. Productivity can also be greatly enhanced by filler metal choice. Using a metal-cored wire with the SAW process, for example, can increase deposition rates by 15 to 30 percent compared to using solid wire, while also offering a wider, shallower penetration profile. Because of their high travel speeds, metal-cored wires can also reduce heat input to minimize weld distortion and the risk of burn-through.
When in doubt, consult with a filler metal manufacturer to determine which wire and flux combinations are best suited for specific applications.
Productivity gains
The SAW process offers great productivity benefits even in its simplest form of single wire welding. The process also offers numerous other options and torch configurations that can additionally benefit productivity, including twin wire, tandem wire and multiwire SAW. While a switch to SAW may involve an upfront investment for companies, its a process change that can pay off in significant productivity gains for many manufacturing and fabrication operations.
If you want to learn more, please visit our website Submerged Arc Hardfacing System.
Submerged-arc welding (SAW) is a common arc welding process that involves the formation of an arc between a continuously fed electrode and the workpiece. A blanket of powdered flux generates a protective gas shield and a slag (and may also be used to add alloying elements to the weld pool) which protects the weld zone.
A shielding gas is not required. The arc is submerged beneath the flux blanket and is not normally visible during welding.
This is a well established and extremely versatile method of welding.
The electrode may be a solid or cored wire or a strip made from sheet or sintered material. The flux may be made by either fusing constituents to form a glassy slag (which is then crushed to form a powder) or by agglomerating the constituents using a binder and a corning process. The chemical nature and size distribution of the flux assists arc stability and determines the mechanical properties of the weld metal and the shape of the bead.
SAW is usually operated as a mechanised process. Welding current (typically between 300 and amperes), arc voltage and travel speed all affect bead shape, depth of penetration and chemical composition of the deposited weld metal. Since the operator cannot observe the weld pool, great reliance must be placed on parameter setting and positioning of the filler wire.
Although SAW is normally operated with a single wire using either AC or DC current, there are a number of variants including the use of two or more wires, adding chopped wire to the joint prior to welding, and the use of metal powder additions. Additional productivity may be gained by feeding a small diameter non-conducting wire into leading edge of the weld pool. This can increase deposition rates by up to 20%. These variants are used in specific situations to improve productivity through increasing deposition rates and/or travel speed. Replacing the wire with a 0.5mm thick strip, typically 60mm wide, enables the process to be used for surfacing components.
Submerged arc welding is ideally suited to the longitudinal and circumferential butt welds required for the manufacture of line pipe and pressure vessels. Welding is normally carried out in the flat (BS EN ISO PA) position because of the high fluidity of the weld pool and molten slag and the need to maintain a flux layer. Fillet joints may also be produced, welding in either the flat or horizontal-vertical (PB) positions.
If you have any questions or need help, us to get expert advice: .
For more MIG Hardfacing Machineinformation, please contact us. We will provide professional answers.