Film, fiber, and non-woven fabrics can be some of the more difficult products to process. Whether introduced to the system in a baled, rolled, or loose form, the tenacity of these products and the tendency for long pieces to self-feed into the shredder rotor means special consideration is required for the design of the machine.

To handle self-feeding products and their tendency to wrap, a second set of nip cutters are used to keep material from winding around the rotor (Figure 2). A further measure may be required to cover the top of the rotor, to limit material feed and put the hydraulic ram in full control of the process.

These materials can also generate heat during the size-reduction process, so cored rotors can be applied that allow for cooling water to flow down the entire length of the rotor. High-power drives, such as a magnetic drive (in Figure 1), can also be used to better process these demanding materials.

Combining the Shredder and Granulator

For repelletizing and densification processes, a 2-3 inch (25-76 mm) particle size is often required, which can be achieved by the shredder alone. If a smaller particle size is required, a combination shredder/granulator system can be supplied.

Drums, barrels, intermediate bulk containers, and other bulky parts can also be a challenge for any size-reduction process. For the shredder, the product size can often determine the size of the machine, versus the processing rate the customer requires. The shredder must have sufficient size to prevent bulky products from bridging in the feed hopper.

Oversized rotors may be required to more efficiently process these large and often hollow parts. Torque is normally not a limiting factor, as these products process easily when introduced into the cutting chamber of the system. For further processing, a particle size of 1/4-3/8 inch (6.4-9.5 mm) is often required, so the use of a secondary granulator would be required.

Pipe and profile (“lineal”) products of ten feet (3 m) or more in length are often processed in a horizontal system (Figure 3), so the parts can be handled without the need for cutting them into to smaller pieces, as would be required for a vertically fed system. A long, vibrating infeed conveyor is used to direct material into an integral pair of nip feed rollers. The nip rollers, much like the ram in a vertically fed system, control the product feed rate into the cutting rotor. Size-reduced particles fall through the sizing screen and can either be mechanically or pneumatically discharged from the shredder.

For pipe and profile products less than ten feet in length, a vertically fed system can be used, and often a tilting table will feed these long parts into the shredder feed hopper, much like drinking straws into a cup.

Purgings, pallets, sheet stacks, railroad ties, and other heavy scrap are a shredder’s best friend, and a granulator’s worst enemy. Due to the feed control of the hydraulic ram, it is almost impossible to overload a shredder with these heavy parts. The shredder’s closed rotor and “chipping” cutters will efficiently process these parts, in some cases all the way down to 3/8 inch (9.5 mm).

However, for highest output and processing efficiency, the addition of a granulator in combination with the shredder is often a good idea. The shredder quickly and easily reduces these large, heavy products to 2-3 inch (25-76 mm) particle sizes for optimum granulator feed. The granulator can then efficiently process these particles to the final desired size. For these processes, a stacked configuration is a common solution for saving money and floor space, as opposed to an in-line system with mechanical conveyors between the shredder and granulator (Figure 4).

Stacking the shredder directly on top of the granulator does, however, greatly reduce the opportunity to detect and/or remove tramp metal. A magnetic plate can be installed between the shredder and granulator to remove ferrous metal; but when large amounts of ferrous and non-ferrous metal are likely, the two should be installed inline, with the proper metal detection and separation systems installed into the mechanical conveyors.

For heavy and/or difficult-to-cut products, additional cutting torque or power may be required. Extra heavy-duty, reinforced shredder frames can also be a good idea for these applications. Additionally, a “P” or passive rotor design is sometimes used to reduce the cutter bite. And “Pipe” packages, including frame, cutting bed, and ram reinforcement, are incorporated for improved machine durability.

A One-Step Shredder

Combination shredding and granulation systems are very popular in plastics applications due to their extreme efficiency and versatility. However, having the ability to effectively size-reduce in one step through a single machine obviously has big advantages. Shredders are being developed now with the power, features, and, most importantly, cutting rotor designs to allow processors to go directly from large, bulky products to the final particle size and consistency for further processing.

The “W” rotor (shown in Figure 5) is a hybrid that combines the traditional coarse “chipping” action of the shredder with the fine cutting action of the granulator. With five rows of cutters and dual bed knives, the “W” rotor has almost five times the cuts per revolution as compared to a traditional shredder rotor. This is the key to being able to size-reduce in one step without sacrificing output and cut quality. The recently introduced V-ECO, with a “W” rotor, is a major advancement towards this ultimate goal.

About the author… Dana Darley is the national sales manager, Plastics Division, for Vecoplan LLC. To learn more about the V-ECO or other Vecoplan systems, contact Darley at ddarley@vecoplanllc.com or U.S. 404-433-1510.