Follow along with the video below to see how to install our site as a web app on your home screen.
JIANZHI supply professional and honest service.
Note: This feature may not be available in some browsers.
THREAD DESIGN
The requirements for NPT (National Pipe Taper) are spelled out
in ANSI B1.20.1
The requirements for NPTF (National Pipe Taper Fuel) are spelled
out in ANSI B1.20.3
Both NPT and NPTF have the same threads-per-inch, pitch diameters, and taper-per-inch. The differences come in the major and minor diameters, the root and crest of the threads.
The NPTF thread crests fall with in the parameters of the NPT requirements, but have a smaller range than the NPT.
The NPTF thread roots are different than the NPT thread roots. NPTF thread roots are designed to interfere with the crest of the mating thread with the intention of creating a mechanical seal through thread form deformation at assembly. NPTF threads have two classes identified: Class 1 and Class 2. NPT thread roots are designed to allow clearance with the mating thread crests on assembly.
PRODUCT ASSEMBLY
NPT threads are designed to screw together. In most cases there
will be no interference between the root and crest of the threads
at assembly. The thread is designed to be assembled with some form
of sealant to assure a leak free joint.
NPTF threads will screw together with NPT threads and should have
no noticeable assembly problem. There will most likely be an interference
fit between the root and crest on either the major or minor diameter
of the thread, depending on which part is NPTF. To accomplish a
seal on the joint, a sealant will be required.
NPTF threads are designed to screw together. They are designed to have interference at the roots and crests of the threads on both the major and minor diameters. This interference should cause no assembly problem. The thread deformation caused by the interference fit and the wrench tightening is designed to make a dry mechanical seal.
Because of the gauging requirements of the NPTF Class 1 product thread, sealant should be used to assure a leak-proof connection. Because of the gauging requirements of the NPTF Class 2 product thread, the seal accomplished through mechanical deformation should require no sealant to make a leak-proof joint. This is critical in some applications where the pipe content is corrosive to chemical sealant.
Want more information on NPT Pipe Fitting? Feel free to contact us.
GAGE REQUIREMENTS
Both NPT and NPTF threads have a requirement for an L1 gage. The
gage is called L1 because it relates to the L1 dimension in the
thread specification. Even though both the NPT's and the NPTF's
L1 requirement are identical, the gages may be different because
of other factors. Specifically, the L1 gages for sizes below and
including 3/8" are identical. The sizes over and including
1/2" are not identical and thus not interchangeable. The difference
between NPT-L1 and NPTF-L1 is at the Plug Gage Major Diameter and
the Ring Gage Minor Diameter.
There are no such NPT gages: L2; L3 or 6-Step Crest Check. If you have NPT gages marked: L2; L3 or 6-Step Crest Check, they are really ANPT gages which have been inappropriately remarked to meet a customer's demand. The gage maker should have educated the customer instead of supplying the incorrectly marked gages. The gages sent to a calibration laboratory, the laboratory should return the gages without calibration because there is no standard which defines the gages.
If your NPT product design requirements indicate additional measurements must be taken, consider changing the product requirement to ANPT per ANSI SAE AS. The NPT and ANPT product threads in the sizes up to and including 2 inches are identical. Beginning at 2-1/2 inches, the wrenching length of the coupling is different between NPT and ANPT product threads. NPT has 2 threads and ANPT has 3 threads.
The NPTF thread standard defines a class 1 and a class 2 thread, also several gage members to measure different features of the product thread.
NPTF Class 1 requires both L1 and L2 ring gages for the male thread and L1 and L3 plug gages for the female thread. Crest Check and Root Check gages are not required for either the internal or external thread. Because of the gauging requirements of the NPTF Class 1 product thread, sealant should be used to assure a leak-proof connection.
NPTF Class 2 requires L1, L2, Crest Check and Root Check ring gages for the male thread and L1, L3, Crest Check and Root Check plug gages for the female thread. Because of the gauging requirements of the NPTF Class 2 product thread, the seal accomplished through mechanical deformation should require no sealant to make a leak-proof joint. This is critical in some applications where the pipe content is corrosive to chemical sealant.
HOW TO USE
Disclaimer:
This data is provided for general information only. The intention is to provide accurate information; regardless; errors may exist in the supplied information. If accuracy is critical, base your final decisions on the data provided in the root documents: ANSI B1.20 and ANSI SAE AS; which are copyrighted documents. To purchase copies visit an Authorized Reseller.
Comments:
Original Posting: 2/28/
Last Revision: 4/08/
Error corrections in, or comments about, the above data can be sent to:
Contact us to discuss your requirements of copper pipe fitting. Our experienced sales team can help you identify the options that best suit your needs.